Handmade speaker basic lecture �C

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 Masao Ida
　It is a basic lecture for making a handmade speaker.
　From a beginner, please also looking-obtain maniacs and enjoy
　a handmade speaker.
　It was made the English version so that he could also understand
　overseas one.
　　　　　　　　　　　　　　　　　　
　Introduction of the speaker of Mr. Nagaoka design
　it is easy to make 500 from the speaker of a certain Mr. Nagaoka, and an
　effect　is high
　The speaker was packed. It goes into a hand about a plan now.
　A thing can be purchased from the acquisition method. It is related with books
　out of print, and is [ this ].
　Please look at E-speaker service and ask a question.

　
　(5) The speaker of 16 cm
　　　　　　　　　　　

The 3rd place

　(1) SS-66 Moai

　 Separate type monitor speaker
　The 3rd place of the Nagaoka speaker BEST10 which a reader chooses
　　　　　　　
　It designs in the form which responds to the hope of the musician K who is
　 also an audiophile.
　When it is what was carried out and there was no severe order of Mr. K, it did
　 not make probably. It is a speaker.

　It is wide and that it is a flat, the main, and a Subwoofer fur are separate
　four points.
　Joge -- in piles -- a floor type and the main -- Bookcase and the main
　It is orders that it can use enough, that it can drive by one set of amplifier
　 etc.

　It wins a great success as a result.

A separate type is that time in a new genre also in the speaker of
　　　　Mr. Nagaoka. It was winning a great success and was set to one of the
　 　　　popular works.

　Upper main Side 250mm A height of 450mm Depth of 345mm
　The 24.4l. of the contents products of Cabinet A length of 8.5cm of a duct
　Lower Subwoofer fur Side 250mm A height of 550mm Depth of 370mm
　The 34.2l. of the contents products of Cabinet A length of 18.5cm of a duct

　 unit FE168�� of the time of manufacture -- x2 FW168x4 FT96Hx2
　 Use 2.5 15mm thick 910×1820mm plywood.
　　　　　　　　

　　The bottoms are original Moai and a unit.

　　　　　　　　　　　　　　
　　　　　　　　　　　　　　　　　
　　　　　　　　　　　　　　
　　　　　　　　　　　　　


･･･････････････････････････････････････････････････････････････････････
　Evolved Moai (evolution of 21st century Moai)

　 SS-66 Moai by which Mr. Nagaoka was designed takes out a face with
　 a popularity vote to a higher rank.
　By the separate formula of two steps of upper and lower sides, the model
　of the unit at the announcement time is changed into a new model now.
　It is carried out.

　The characteristic summarized how for how sound changes.
　　　　　　　
　　　　　　　　　
･････････････････････････････････････････････････････････････････････････
　 Evolution of Moai
　 The sound of Moaiwhich used the present unit and evolved can be used also
　 as a monitor.
　It had the wonderful wide range of a degree and evolved into a speedy sound.
　The plan is using the same thing as the original of Mr. Nagaoka.

　new unit The upper row FE168E�� -- x2 FT96 A-EXx2
　Lower berth FW168Nx4

　　　　　　　　　　　
　　　　
　The unit and network which were used for evolution of Moai
　　　　　　



　　　Attachment of T96 A-EX

　


　Sound and the characteristic of having evolved

　 When a new style unit is exchanged, it is large improvement in tone quality
　 without making sense of incongruity hold.
　It has The exchanged unit is the succeeding model of the same Fostex.
　Therefore, the which is not considered as change of all plans although
　 a thing with sufficient affinity is not wonderful, either
　having been settled firmly so far -- present -- business -- isn't it good
　news in the inner one, either?
　　　　
　 The recording monitor to which it had a wonderful wide range and speediness
　 was equal all over the districts
　　Even if it carries out, the sound and this which can be used are the feature
　 of　Moai

　This became a new style unit and was upgraded further. Especially T96 A-EX is.
　It is more fascinating and the high region which is full of a feeling of substance
　jumps　out. This super-Loud-sound region
　A pleasant sensation is irreplaceable.


　T96 A-EX (limited vending machine kind)
　　　8ohms / 103dB / 4kHz - 40kHz

　　　　　　　　* The 21st [ -] century of reference Evolution of Moai
　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 Report Akira Sumiyama
.........................................................................................................................
.

　Moai is made.

　 If three ways are purchased with a commercial speaker, we will recommend
　you Moai.
　It is not difficult to make only because of a box. A vertical bus reflex structure
　sake
　It is making the duct of a bus reflex correctly.

　A unit, a wiring code, capacitor CS0.47micro F, and coil LS2.2mH
　Making a capacitor cheap, although it is required, CT0.47micro F and a coil are
　L3.5mH.
　It can also carry out. A reason is the newest network element, if original.
　It does not use. The conventional thing is also arranged enough.
　　　　　　

　 Although there is a size a height of 1m, the side is not so large as 25cm.
　 Although it is a tall　boy
　The view of a network element differs from the speaker of three commercial
　 ways.

　A network is very simple and are a coil and one capacitor.

　This is carrying out the work which makes it simple by Nagaoka style and
　 employs the sound of unit original efficiently.
　Maker make is a coil and a capacitor in a complicated network, if it is said
　 [ how ] whether be.
　Since a lot is used, the freshness of sound falls.

　Since it does not make artificially, for a network, sound is simply as it can do.
　The power which a unit has by carrying out is efficiently employed in the
　maximum.

Moai is a developed type. Since it can do in the combination of a unit
　　　　 it is a back load.
　　　　　A phon is the speaker which is completely different.
　


　　　　　　　　　　　　　　　　　　　　　　　
　

　
The 9th place

　(2) D-168 Super Rare
　　　　　　　　　　　　　　　
　An original super rare (FE168SS use)
　　　　　　　　　　　　　　　　
　 Rare is the small ostrich which lives in South America, and Mr. Nagaoka is a
　swan.　I think that it named by the large thing.

　At 16cm, the design of the back load phon of Mr. Nagaoka is super rare.
　There is D-37. The original unit was both FE168SS.
　　　　　　　　　　　　　　　　　　　　
　　　　　　　　　　　　　Rare (alias United States ostrich)

　 The difference in a character
　The comment of very interesting Mr. Nagaoka the sound which attaches
　 FE168SS It is.
　　　　　　　　　D-37= monitor tone
　　　　　　　　　super rare = music nature

　It is both wide and they are a flat and high efficiency.
　if compared with a 10cm super swan -- a super rare one -- hard
　It is powerful and is dynamic.
　　　　　　　　

　 The breadth of 450mm, the depth of 470mm, and 全 quantity are 1130mm.
　the center of a floor to a unit -- until -- the position of the ear when applying
　 to 1015mm and a sofa
　It is alike, and it is designed so that it may come.

　Board thickness uses 15mm and four 3x6 plywood.
　basic structure -- a super swan -- the same -- the back load phon of a rear
　 surface　opening
　The whole is made from a head, Pipe, a body, and three.

　 Assembly
　How to assemble is a D-101S super swan because of the same structure as a
　super swan.
　Please give me. Here is explaining in more detail.


If an assembly works as the turn of distance, it will be satisfactory first.
　　a whitish image [ like a swan ] whose paint is -- the method of brown finish
　　wooden clogs
　　It seems to be good. Although it will be teak material if it says byThurs
　　 a paint　is good at his liking.


　　 D-168 super rare plan

　　　Four A board is cut. 15mm 910x1820mm plywood use
　　　　　　　
　　　　　　　　
　　　　　　　　　　　　　　　　　　　　Assembly figure


　　　　　　　　　　　　　　　　 　　

　　　　　　　　　　　　　　　　　　　A head and Pipe

　　　　　　

　　　　　　　　　　　　　　　　　　　Structure of a body


　　　　　　　 　　　　　
　　　　　　　　　　　　　　　　Original main material
　　　　　　　　　　　　　　　　Turn of assembly distance



　　　　　　　　　　　　　　　　　　　　　　　
　

　
　(3) D-37

　 FE168ES (limited sale)
　It corresponds to FE168E �� (unit only for back loads of the H.P. oscillating
　 version).
　It is the design for FE168SS at the time of manufacture. A unit can use ES
　and E��.
　It can sound with the room of 6 to 8 mats as a 16cm back load phon.

　A basic design is a slender tall boy in D-57.
　　　　　　
　powerful -- D-37 completed by unit FE168SS
　 The unit of the time of a design was FE168sigma. powerless on a back load
　It was not the best in a unit. The cabinet with the it same at the appearance
　 of SS
　When it was alike and SS was attached, it experimented in what becomes.

　It was the sound of a special different dimension. and there is a powerful scale
　It became sound.

　 How is it in unit FE166 ES-R of limited sale?
　From present FE166Esigma, since a magnet is powerful, it is in reproduction of
　 heavy low-pitched sound.
　It becomes advantageous.

　Since loud sound and low-pitched sound are between 10cm and 20cm musically
　 the degree of 16cm is good.
　There is the feature to reproduce.
　The room also has the merit which can fully be sounded with 6 mats.

　A conclusion is arranged enough.
　A part to have been upgraded is useful to reproduction of low-pitched sound.



　 The depth of 45cm, a width of 240mm of Speaker attachment hole, and full
　 length are 1000mm.
　Since board thickness is 15mm, a reinforcement board is attached in all boards
　 and intensity is a problem.
　There is nothing. The side of basic structure is the same as that of D-58 grade
　at 30mm.

　 Carry out five-sheet weak use of the 15mm thick　910×1820mm plywood.
　It is the speaker which becomes main.

　 The addition of Tweeter
　Loud sound will become beautiful if super Tweeter is connected only by the
　capacitor.
　It connects with film capacitor 0.47micro F or 0.68 micro F by reverse .
　Although super Tweeter is arranged by FT96H, T90A, and T925A
　the thing in this with the lowest efficiency -- FT96H -- efficiency is higher
　than it but
　We recommend you T90A.
　　　　　　　　　　　　

* Since it is the same as D-58ES about an assembly, it is handmade
　 speaker D-58ES. Please give me
　Since this is entering a manufacture process photograph, the one where
　 handmade is the more nearly first is also understood.
　　I consider.

　　　　　　　　　　　　　　　　　
　　　　　　　　　　　　　　　　　　　　Original D-37

　　　　　　　　　　
　　　　　　　　　　　　　　　　　　　The plan of D-37



　　　　　　　　　　　　　　　　　　　Assembly figure
　　　　

　　　　　　　　　　　　　　　　　　
　　　　　　　　
　　　　　　　　　　　　An assembler is a figure. Main material





　　　　　　　　　　　　　　　　　　　
　　　　　　　　　　　　　　　　　　　　D-37 Unit FE168ES




　

　�C-1 F2000 Nessie Jr

　 Correspond to FE168E �� (unit only for back loads of the H.P. oscillating
　 version).

　It was designed for NessieJrFE166 �敗 and is at Nessie for Nagaoka.
　Since there is height in ordinary homes, it does not enter. Then, it was
　 improved by　home use.
　is NessieJr. being effective as an object for Surround-- the -- peculiar
　It is the masterpiece currently made from the form by many people.

　 Assemble by 3 blocks of a resonance pipe, a main part, and a top pipe.
　 Top A pipe is slid and can be fixed by ceiling quantity.

　 Use four 15mm thick 910×1820mm plywood.

　The bottom is F2000 Nessie Jr.
　　　　　　　　　　　　　　


　�C-2 Nessie Jr ES version

　 Differ from the design of above Nessie　Jr with the version version for
　　FE168ES.
　a cabinet is powerful -- in order to unite with unit FE168ES -- a resonance
　 pipe
　The cross-section area is expanded a little 20%.
　The position of a unit also became high.

　the height of quantity -- replacing with -- there are a front opening type
　 and
　 an upper part opening type like
　 Use five 15mm thick 910×1820mm plywood.

　 The error of a plan and explanation
　Plan (audio accessories company) 2001 No. 102 per year
　There is an error in explanation of this number.


　(1) Although it is 18mm apiton plywood, it is the error which is 15mm.
　However, a plan can be made now from 15mm.

　(2) Although it is four 910×1820mm plywood, use five sheets.

　2 pattern community board x1 2 pattern community board x2
　a top -- taking out -- the object for a type -- x2 or front appearance
　-- carrying out -- the object for a type -- xtwo
　Three sheets and the object for a type become [ a common board ] a total of five sheets by two sheets.
　　　　　　　


　* The correction report of audio accessories No. 102 *

　It sets in "a quarterly issue and the audio accessories No. 102", and is
　between the followings.
　Better with While apologizing to you, a reader, and the Gentlemen concerned
　I will correct here.

　 NessieJr.ES of "the method ship project of a mini" which begins from 187
　 pages
　manufacture -- use Thickness of the board carried out although indicated as
　 18mm --right
　A 15mm apiton board is used. It is carrying out.

　A 190-page figure is also the drawing of 15mm The direction manufactured
　 is given.
　　　　　　　　being also prodigal -- be careful
　　　　　　　　　　　 18mm thick apiton board
　　　　　　　　　　　　　　　　　　↓
　　　　　　(Positive) 15mm thick apiton board



　　　　　　　　　The bottom was manufactured by ES version.
　　　　　　　　　　　　　　　　　Unit FE168ES
　　　　　　　　　　　　　　　　　　


　　　* Look at and pass here and it is a link.