SPI sound plaza Ida / handmade speaker QS106 rear canon II.page

Manufacture of QS-106 Rear Canon II
August 16, 2001 completion
(Manufacture days three months)

　 What was used for Rear Canon II

　China plywood(910×1820mm board　15mmx3)
　 edited one by the collection of plan ( speaker- things -
　　there is nothing) drawings

　A woodwork bond, wood putty, wood-carving oil, urethane varnish
　The tool used in order to raise accuracy Bolting metallic
　ornaments

　The code for terminal (T-100x2) wiring of FOSTEX, Sandpaper
　Unit FOSTEX (FE108 ES, FE108E∑x 2)
　* Plywood uses 910mmx1820mm.

　 By coverage of the "stereo" magazine in purpose-June, 2001

　I thought that he wanted to upgrade the present rear speaker.

　I want to make rich the feeling of a spread of sound of the
　 sound of a DVD audio.
　Since AV amplifier TX-DS989 was upgraded, it is rear.
　The back's speaker is needed.

　 a result -DVD audio - the beauty of a feeling of a spread, and
　sound 　It comes to be wrapped.
　 To manufacture of after that Nessie Jr
　A feeling of a sound place only carries out having become
　 good, and its power is still weak.
　Limited sale of the FE168-ES is carried out, this is used, and
　 it is the increase in a feeling of a sound place.
　I want to have come to make Nessie Jr as Purpose.

　　　　　　　　　

　- The comment of Mr. Nagaoka -

　 It was designed and manufactured by exclusive use as a
　 rear speaker used by "way ship."
　FE108ES a unit through FE106sigma to FE108sigma at the
　 time of manufacture
　Although attached, the box has not changed from the time of
　 manufacture.
　Size is 225x225x1595mm in square pillar form, and is 400mm
　 from an upper end.
　Sub attachment hole of a speaker of unit attachment is
　 attached [ of the 2nd page ] by Position.
　It is J form resonance pipe of 1-time bending as canon
　 fellows' basic structure, and is a pipe.
　Full length is set to 3m.

　Material takes the component for two sets for 15mm China
　 plywood by three use.
　Since cautions are considerably needed for an assembly and
　there is also a difficult portion somewhat
　Tools, such as a tool Bolting metallic ornaments, are prepared
　and it is carefully.
　It will be necessary to assemble over many hours.
　The junction side of a board sticks completely and it is
　[ few air leaks and ] imperfection.

　That it is careful as much as possible so that there may be
　no generating which comes from adhesion and which cries
　It is important.

　 Two must be assembled so that it may become L.R symmetrical
　 type.
　When coming out and combining a component, it is important
　to pay attention enough.
　 Attach a terminal in the lower part of board (7).
　Two units are parallel connection.

　 Manufacture of my Rear Canon II

　(1) Making to right-and-left symmetry checks difficult NO of
　a plan and is careful.
　The component was constructed, divided and made from the
　 start to construct on the right and the left.

　(2) For the resonance pipe, the hole was vacant with wood
　putty so that there might be no air leak. The place was filled.

　(3) The inside was made 2 times coating of urethane varnish.
　The direction which applies an inside is sound.
　It becomes good.
　(4) 2 times coating and urethane varnish of wood-carving oil
　apply an outside 3 times, and come out of it. It has finished.
　It applies thickly with urethane varnish. Gloss comes out. It is
　finished beautifully.
　If it gets dry, it will polish by fine Sandpaper. Applying uniformly
　is that it is unexpected.

　It is difficult. For the portion to which especially the paint has
　 become thick, unevenness is appearance and す.
　it is -- cautions are required

・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
　Like an assembler
　　　　　　　(1+2)+(3+4)+5+6(7+8)+9+(10+11+12+13)
　　　　　　　+(14+15)+(16+17+18+19)+20

　The plan of Rear Canon II
　It is three-sheet use about 15mm plywood.
　With 910mmx1820mm plywood, it is x1 and x2 from a top.
　Please [ expansion / of a plan / from / here ]
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

　 Merit of Rear Canon

　rear ones of a home theater - the bicycle trailer which has
　 the feeling of a spread of sound as business
　Non is satisfactory. I am using for Back rear of 7.1ch(es).
　A unit is FE108E∑, if it does not choose and is 10cm full range.
　FX120 and F120A can also be used in an ES and ESII12cm full range

　About a Resonance pipe, it is a handmade speaker basic lecture.
　It is alike and is explaining. Please look at here. 　
　　　　　　　　

6/25Arrival of plywood	The terminal was attached. The product made from フォステクス	The size of plywood Check	Grain is checked. The board to be used is decided.
NO entry of a drawing It enters with the pencil.	The inside of a resonance pipe It is the first and the second and is 3M. Height 1M60	7/14 inside completion An inside is wood carving. 1-time coating of oil	Restoration of a hole Air leak There needs to be nothing.
Wood-carving oil and varnish previously - oil - getting dry Urethane varnish is applied. To apply thickly is good.	coating It is also sound if it applies beautifully. It becomes beautiful. It polishes by Sandpaper.	The stand not falling If it is [ this ] still Since it falls, a stand is made.	8/16 completion there is a spread Sound is wonderful.

Manufacture of QS-106 Rear Canon II August 16, 2001 completion (Manufacture days three months)

The terminal was attached. The product made from フォステクス

The size of plywood Check

Grain is checked. The board to be used is decided.

NO entry of a drawing It enters with the pencil.

The inside of a resonance pipe It is the first and the second and is 3M. Height 1M60

7/14 inside completion An inside is wood carving. 1-time coating of oil

Restoration of a hole Air leak There needs to be nothing.

Wood-carving oil and varnish previously - oil - getting dry Urethane varnish is applied. To apply thickly is good.

coating It is also sound if it applies beautifully. It becomes beautiful. It polishes by Sandpaper.

The stand not falling If it is [ this ] still Since it falls, a stand is made.

8/16 completion there is a spread Sound is wonderful.

Manufacture of QS-106 Rear Canon II
August 16, 2001 completion
(Manufacture days three months)

The terminal was
attached.
The product made from フォステクス

The size of
plywood Check

Grain is checked.
The board to be
used is decided.

NO entry of a
drawing It enters
with the pencil.

The inside of a
resonance pipe
It is the first and
the second and is 3M.
Height 1M60

7/14 inside completion
An inside is wood
carving. 1-time
coating of oil

Restoration of
a hole Air leak
There needs to be
nothing.

Wood-carving oil
and varnish
previously - oil - getting
dry Urethane varnish
is applied.
To apply thickly is good.

coating
It is also sound if it applies beautifully.
It becomes beautiful.
It polishes by Sandpaper.

The stand not falling
If it is [ this ] still
Since it falls,
a stand is made.

8/16 completion
there is a spread
Sound is wonderful.